What's New

Bug Fixes and Optimizations

• Fixed a few known issues to enhance the system's performance

What's New

Bug Fixes and Optimizations

• Fixed a few known issues to enhance the system's performance

Notes

To fully utilize all the new features in Autel Explorer V2 app, it's important to update your EVO II V2 firmware to V2.4.35 or higher before flying. Note that firmware versions below V2.4.35 will NOT be compatible with Autel Explorer V2 app.

Resources

• EVO II V2 Firmware: https://www.autelrobotics.com/download/421

• Please read through the update instruction for Autel Explorer V2 app & firmware V2.4.35 carefully before the update: https://www.autelrobotics.com/articledetail/Explorer-V2-app-announcement

New Feature

• Added support for the new camera model: XL706 (6K Pro)

• Note: The XL706 (6K Pro) does not support panoramic features.

• Added system certification information

Bug fixes and optimizations

• Optimized aircraft wind resistance performance to comply with Chinese regulatory standards.

• Removed low battery warning in Attitude Mode.

• Fixed altitude deviation during rapid vertical movement in GNSS mode.

• Fixed false no-fly zone alerts under weak GNSS signal conditions.

• Fixed an issue where the “Gimbal Initialization Failed” error occurred after calibrating the gimbal and then power cycling the aircraft.

• Fixed issues with auto-uploading flight records to third-party platforms.

• Fixed other known issues.

Notes

• Android system V1.3.9.23 is only for EVO II V3

• To fully utilize all the new features in V3.1.134 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.4.4 before flying.

Resource

• EVO II V3 Manual Update Instructions: https://drive.google.com/file/d/1ANqz_wZqCmUN-QgWWMgJcFGAN_RsirTf/view?usp=sharing

• Livedeck II Firmware: https://www.autelrobotics.com/doc/evoii-livedeck-ii-firmware

• V3 Smart Controller Android System: https://www.autelrobotics.com/download/559.html

• Autel Explorer App: https://www.autelrobotics.com/download/27

• EVO II V3 Firmware: https://www.autelrobotics.com/download/543.html

• EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/544.html

Update Method & Steps:

• OTA Update:

1. Please ensure that the internet connection remains stable throughout the process.

2. Open the Explorer app and tap the settings icon in the camera view.

3. Go to General, then select Software Update, and tap on Android System.

4. Click on Start Updating.

5. The update process should take approximately 15 minutes to complete.

6. Once the update is finished, the controller will automatically power cycle.

• Manual Update:

1. Begin by downloading the Android System zip file.

2. Transfer the downloaded file onto an SD card.

3. Insert the SD card into the Smart Controller. If needed, you can utilize a USB converter for this step.

4. Navigate to Settings > General > Software Update > Android System.

5. Select the option for USB flash disk update.

6. Choose the file from the SD card and initiate the manual update process.

What's New

New Features

• Added Remote ID function in China

• Added Pairing method: Double click battery power button to enter pairing mode

Bug fixes and optimizations

• Optimized video transmission feed performance

• Optimized No-fly zone function

• Optimized Remote ID function

• Optimized HDMI function

• Fixed GPS update error issue

• Fixed other known issues.

Notes

• Android system V1.3.9.15 is only for EVO II V3

• To fully utilize all the new features in V3.1.107 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.1.78 before flying.

Resource

• Livedeck II Firmware:https://www.autelrobotics.com/doc/livedeck_ii_firmware

• V3 Smart Controller Android System:https://www.autelrobotics.com/download/572.html

• Autel Explorer App: https://www.autelrobotics.com/download/113

• EVO II V3 Firmware: https://www.autelrobotics.com/download/547.html

• EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/548.html

Update Method & Steps:

• OTA Update:

1. Please ensure that the internet connection remains stable throughout the process.

2. Open the Explorer app and tap the settings icon in the camera view.

3. Go to General, then select Software Update, and tap on Android System.

4. Click on Start Updating.

5. The update process should take approximately 15 minutes to complete.

6. Once the update is finished, the controller will automatically power cycle.

• Manual Update:

1. Begin by downloading the Android System zip file.

2. Transfer the downloaded file onto an SD card.

3. Insert the SD card into the Smart Controller. If needed, you can utilize a USB converter for this step.

4. Navigate to Settings > General > Software Update > Android System.

5. Select the option for USB flash disk update.

6. Choose the file from the SD card and initiate the manual update process.

New Features

• Clear View Mode: Hide status bar and flight information on-screen

• RTSP Streaming: Stream video to third-party platforms like VLC using Livedeck II WiFi

Bug fixes and optimizations

• Optimized streaming performance

• Fixed other known issues.

Note

• Livedeck II is only compatible with EVO II V3.

• Only EVO II V3 firmware version V1.1.78 or above is compatible with Livedeck II V1.0..24.

Resource

• V3 Smart Controller Android System https://www.autelrobotics.com/download/572.html

• Autel Explorer App: https://www.autelrobotics.com/download/113

• EVO II V3 Firmware: https://www.autelrobotics.com/download/547.html

• EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/548.html

Manual Update Steps:

1. Turn on the Livedeck II firmware and wait a minute for the system to start up.

2. Download the Livedeck II firmware to a microSD card.

3. Insert the microSD card into the slot on the back of your Livedeck II firmware.

4. After a few seconds, the battery LED indicator light will begin flashing alternately, indicating that the update process has started. Allow the update to proceed for 10 minutes.

5. After 10 minutes, power cycle your Livedeck II and verify the firmware version.

Check Livedeck II Firmware Version ( Video Reference)

1. Power on both the V3 Smart Controller and the Livedeck II.

2. Connect the V3 Smart Controller and the Livedeck II using a USB-A to USB-C cable. (Connect USB-A to the Livedeck II and USB-C to the V3 Smart Controller).

3. Go to Settings > Connected devices > USB on the V3 Smart Controller.

4. Choose USB tethering for USE USB FOR section.

5. Open the Autel Explorer App on the V3 Smart Controller and wait for a few seconds. The Livedeck II settings page will appear automatically.

6. Once you see the Livedeck II settings page, navigate to About and then Firmware Version to view the Livedeck II firmware version.

Firmware Version Table

New Features

• Added support for the new camera model: XL706 (6K Pro)

• Note: The XL706 (6K Pro) does not support panoramic features.

• Added system certification information

Bug fixes and optimizations

• Optimized aircraft wind resistance performance to comply with Chinese regulatory standards.

• Removed low battery warning in Attitude Mode.

• Fixed altitude deviation during rapid vertical movement in GNSS mode.

• Fixed false no-fly zone alerts under weak GNSS signal conditions.

• Fixed an issue where the “Gimbal Initialization Failed” error occurred after calibrating the gimbal and then power cycling the aircraft.

• Fixed issues with auto-uploading flight records to third-party platforms.

• Fixed other known issues.

Note

• Firmware V1.4.4 is only for EVO II V3

• Once the aircraft has been updated to V1.4.4, it will no longer be possible to downgrade to a lower version.

• To fully utilize all the new features in V3.1.134 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.4.4 and Android System to V1.3.9.23 before flying.

Resource

• EVO II V3 Manual Update Instructions: https://drive.google.com/file/d/1ANqz_wZqCmUN-QgWWMgJcFGAN_RsirTf/view?usp=sharing

• Livedeck II Firmware: https://www.autelrobotics.com/doc/evoii-livedeck-ii-firmware

• V3 Smart Controller Android System: https://www.autelrobotics.com/download/559.html

• Autel Explorer App: https://www.autelrobotics.com/download/27

• EVO II V3 Firmware: https://www.autelrobotics.com/download/543.html

• EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/544.html

New Features

• Added Remote ID function in China

• Added Pairing method: Double click battery power button to enter pairing mode

Bug fixes and optimizations

• Optimized video transmission feed performance

• Optimized No-fly zone function

• Optimized Remote ID function

• Optimized HDMI function

• Fixed GPS update error issue

• Fixed other known issues.

Note

• Firmware V1.1.78 is only for EVO II V3

• To fully utilize all the new features in V3.1.107 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.1.78 and android system to V1.3.9.15 before flying.

• If your GPS is not on the latest version, please update the firmware to V1.1.78 again. If the GPS still has issues, please contact us at support@autelrobotics.com or call (844) 692-8835.

Resource

• Livedeck II Firmware: https://www.autelrobotics.com/doc/livedeck_ii_firmware

• V3 Smart Controller Android System: https://www.autelrobotics.com/download/572.html

• Autel Explorer App: https://www.autelrobotics.com/download/113

• EVO II V3 Firmware: https://www.autelrobotics.com/download/547.html

• EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/548.html

What's New

Bug Fixes and Optimizations

• Fixed other known issues

Notes

To fully utilize all the new features in the V2.4.43 firmware, it is important to install Autel Explorer V2 app before updating the firmware. Note that Autel Explorer app (without V2) is NOT compatible with this firmware version.

Resources

• Autel Explorer V2 App: https://www.autelrobotics.com/download/436

• Please read through the update instruction for Autel Explorer V2 app & firmware carefully before the update: https://www.autelrobotics.com/articledetail/Explorer-V2-app-announcement

What's New